La recepción de UART no funciona en STM8S

Soy nuevo en stm8 (stm8s003f3p) Lo he hecho siguiendo el código pero no pude encontrar lo que está mal con él. La transmisión UART está funcionando pero no se pudo recibir nada.

#include <iostm8s003f3.h>
#include <intrinsics.h>
#include <stdio.h>

void InitialiseSystemClock()
{
    CLK_ICKR = 0;                       //  Reset the Internal Clock Register.
    CLK_ICKR_HSIEN = 1;                 //  Enable the HSI.
    CLK_ECKR = 0;                       //  Disable the external clock.
    while (CLK_ICKR_HSIRDY == 0);       //  Wait for the HSI to be ready for use.
    CLK_CKDIVR = 0;                     //  Ensure the clocks are running at full speed.
    CLK_PCKENR1 = 0xff;                 //  Enable all peripheral clocks.
    CLK_PCKENR2 = 0xff;                 //  Ditto.
    CLK_CCOR = 0;                       //  Turn off CCO.
    CLK_HSITRIMR = 0;                   //  Turn off any HSIU trimming.
    CLK_SWIMCCR = 0;                    //  Set SWIM to run at clock / 2.
    CLK_SWR = 0xe1;                     //  Use HSI as the clock source.
    CLK_SWCR = 0;                       //  Reset the clock switch control register.
    CLK_SWCR_SWEN = 1;                  //  Enable switching.
    while (CLK_SWCR_SWBSY != 0);        //  Pause while the clock switch isbusy.
}

void InitialiseUART()
{
    unsigned char tmp = UART1_SR;
    tmp = UART1_DR;
    UART1_CR1 = 0;
    UART1_CR2 = 0;
    UART1_CR4 = 0;
    UART1_CR3 = 0;
    UART1_CR5 = 0;
    UART1_GTR = 0;
    UART1_PSCR = 0;
    UART1_CR1_M = 0;        //  8 Data bits.
    UART1_CR1_PCEN = 0;     //  Disable parity.
    UART1_CR3_STOP = 0;     //  1 stop bit.
    UART1_BRR2 = 0x02;      //  Set the baud rate registers to 9600 baud
    UART1_BRR1 = 0x68;      //  based upon a 16 MHz system clock.
    UART1_CR2_TEN = 0;      //  Disable transmit.
    UART1_CR2_REN = 0;      //  Disable receive.
    UART1_CR3_CPOL = 1;
    UART1_CR3_CPHA = 1;
    UART1_CR3_LBCL = 1;
    UART1_CR2_TEN = 1;
    UART1_CR2_REN = 1;
    UART1_CR3_CKEN = 1;
}

void UARTPrintF(char *message)
{
    char *ch = message;
    while (*ch)
    {
        UART1_DR = (unsigned char) *ch;     //  Put the next character into the data transmission register.
        while (UART1_SR_TXE == 0);          //  Wait for transmission to complete.
        ch++;                               //  Grab the next character.
    }
}

unsigned char RecUART1(void)
{
    while (!(UART1_SR_RXNE));    // USART_SR[5]:RXNE   Read data register not empty
    PD_ODR |= (1<<2);                                      //   0: Data is not received, 1: Received data is ready to be read.
    return UART1_DR;
}

int main( void )
{
    unsigned char out;
    char dis[25];
    // PD_DDR = (1<<5)|(1<<2);
    //PD_CR1 |= (1<<2);
    //*out ='l';
    //in=out;
    __disable_interrupt();
    InitialiseSystemClock();
    InitialiseUART();
    __enable_interrupt();
    while (1)
    {
        out = RecUART1();

        //for (long counter = 0; counter < 250000; counter++);
        sprintf(dis,"this is %c\n",out);
        UARTPrintF(dis);
    }
}